MMIC BMS and EMS Annual Maintenance and Validation
Published
Description
The BMS and EMS system currently runs on Siemens Desigo CC and the facility is on the course to being a fully GMP compliant facility. There are currently ten BMS panels on the site with several sensors and control points that feed into these panels from various cleanroom and plant equipment. Our EMS and BMS systems both use the same sensors for control and monitoring but operate slightly differently. Our EMS system is fully audit trailed and validated yearly to keep this in line with GMP requirements. The EMS monitors all data coming from our clean rooms which monitors the temperature, humidity, airflow, and differential pressure across all four cleanrooms, service corridors and auxiliary areas. On site we currently have the below equipment and system checks required to be covered under the service agreement o 4 cleanrooms all fitted with 2 control panels, 4 differential pressure probes along with a temperature and humidity sensor. Each it will need to be fully calibrated annually along with all calibration reports provided. o We currently have 11 air handlers in total, 5 of these feed into our cleanroom areas while the other 6 units feed into control offices and event areas. All units have 2 fan speed controllers, 7 pressure transmitters, 1 fresh air temperature sensor, 3 temperature humidity sensors and 2 velocity meters. All of which require to be calibrated annually along with calibration reports. o Differential pressure switches that will need to be inspected to ensure the electrical operation of the circuit is running as it should. o As well as this, the switch setting must be checked, and you must ensure that it responds to changes in pressure. o Air and water flow switches that will need to be inspected to ensure the electrical operation of the circuit is running as it should. The switch setting must be checked to ensure that it responds to change in flow. Actuators/Valves/Dampers/Water Meters- Check the operation of actuators across their full stroke and ensure correct positioning over the analogue output range. Ensure actuator limit switches operate correctly along with Check power fail action operates correctly by simulating mains failure. Check valves for leaks and repair where applicable and ensure minimum let-by in the closed position. Check that the valve and damper linkage are fitted securely. Check that damper blades and linkage operates operate correctly throughout their range, without undue stiffness. Advise relevant Building Services Engineer of any mechanical problems. o Control Checks - Check the stability of all plant visually along with System Operation Checks. Authorisation will be sought from a member of the CPI operational Engineering team prior to isolating any plant, and care will be taken that any checks do not unduly affect environmental conditions. The system will be set to its 'off' condition (where possible) and check correct response of all controlled equipment. Along with Simu... Additional information: For more information please see the tender documentation, that is free to access on https://in-tendhost.co.uk/uk-cpi/ Is a Recurrent Procurement Type? : No
Timeline
Publish date
a month ago
Close date
17 days ago
Buyer information
Centre for Process Innovation
- Contact:
- Daisy Irving
- Email:
- daisy.irving@uk-cpi.com
Explore contracts and tenders relating to Centre for Process Innovation
Go to buyer profileNotice topics
Source
Contracts FinderTo save this opportunity, sign up to Stotles for free.
Save in appTender tracking
Access a feed of government opportunities tailored to you, in one view. Receive email alerts and integrate with your CRM to stay up-to-date.
Proactive prospecting
Get ahead of competitors by reaching out to key decision-makers within buying organisations directly.
360° account briefings
Create in-depth briefings on buyer organisations based on their historical & upcoming procurement activity.
Collaboration tools
Streamline sales workflows with team collaboration and communication features, and integrate with your favourite sales tools.
Explore similar tenders and contracts
Browse open tenders, recent contract awards and upcoming contract expiries that match similar CPV codes.
- Openclosing
TC01351 - Zone 4 & 5, Block E & F, Conductor Rail, Safety Fence & LV Cabling for AERTG
Hutchison Ports (UK) Limited2,100,000 GBPPublished 4 days ago
- Openclosing
Heat Decarbonisation Strategy, Desktop assessment and Building audit
University of CumbriaPublished 6 days ago
- Openclosing
TC01307 - The Service and Repair of Direct Current ("DC") and Alternating Current ("AC") Electric Motors
Hutchison Ports (UK) LimitedPublished 6 days ago
- Openclosing
Building and Safety Regulation - Research and Evaluation Framework
GOV11,000,000 GBPPublished 7 days ago
- Openclosing
Building and Safety Regulation - Research and Evaluation Framework
GOV11,000,000 GBPPublished 7 days ago
- Openclosing
Electrical Trade Products Framework
Bournemouth Christchurch and Poole CouncilPublished 12 days ago
- Openclosing
Electrical Trade Products Framework
Bournemouth Christchurch and Poole Council2,800,000 GBPPublished 12 days ago
- Openclosing
Electrical Trade Products Framework
Bournemouth Christchurch and Poole Council2,650,000 GBPPublished 12 days ago
Explore other contracts published by Centre for Process Innovation
Explore more open tenders, recent contract awards and upcoming contract expiries published by Centre for Process Innovation.
- Openclosing
Building CPI's capability in industrial connectivity, Federated Learning and data science methodologies
Centre for Process InnovationPublished 13 days ago
- Openclosing
E-Lab – Electronic Laboratory Notebook Software Package
Centre for Process InnovationPublished 24 days ago
- Openclosing
E-Lab - Electronic Laboratory Notebook Software Package
Centre for Process Innovation900,000 GBPPublished 25 days ago
- Openclosing
Building CPI’s capability in industrial connectivity, Federated Learning and data science methodologies
Centre for Process Innovation1,000,000 GBPPublished a month ago
- Openclosing
Multifunctional Polymer Chemistry Pilot Plant Pilot Plant and Modification/Upgrades to Facility
Centre for Process InnovationPublished a month ago
- Closed
Extending CPI's capability in Data Analytics, Adaptive Design-of-Experiments and Support for Federated Learning
Centre for Process InnovationPublished a month ago
- Openclosing
Multifunctional Polymer Chemistry Pilot Plant Pilot Plant and Modification/Upgrades to Facility
Centre for Process Innovation2,000,000 GBPPublished a month ago
- Closed
Recyclability Test Equipment for Packaging Materials
Centre for Process InnovationPublished a month ago
- Closed
MMIC BMS and EMS Annual Maintenance and Validation
Centre for Process InnovationPublished a month ago
Explore more suppliers to Centre for Process Innovation
Sign upExplore top buyers for public sector contracts
Discover open tenders, contract awards and upcoming contract expiries of thousands of public sector buyers below. Gain insights into their procurement activity, historical purchasing trends and more.
Explore top sources for public sector contracts
Stotles aggregates public sector contract data from every major procurement data source. We ingest this data and surface the most relevant insights for our users. Explore our list of public sector procurement data sources below.